Free Quote

 

 

On this page below you will discover some dependable information on the subject of How to Install a Bathtub Yourself.

Setting up a tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably challenging job. If the old bathtub is easily easily accessible, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you may need a specialist plumber to make tube links.
This article will certainly aid you set up a brand-new tub in your restroom if you have actually currently gotten a new tub and don't require to alter the plan of your previous supply of water pipes.
Your devices and also product checklist should comprise the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installation

To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final position.

 

 

Removing Old Touches

If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite problematic because of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

 

 

Setting up the Tub

Utilizing both wooden boards under its feet, put the tub in the needed setting. The wooden boards are useful in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bath tub till the level checks out level.
To install taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the supply of water and check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been used at the very least once as this will certainly settle it right into its final position.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in location in between the tap as well as the sink. Secure the faucet in position with the producer given backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Tub

In the location where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall between the bathroom and also the tiling, leading to problems with moisture and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Remember to always load the bath tub with water before sealing, to enable the activity experienced when the tub remains in usage. The sealant can crack relatively very early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a passionate person who reads about How to Install a Bathtub, I figured sharing that piece of content was a smart idea. Remember to take the time to share this write-up if you enjoyed it. I thank you for reading our article about How to Install a Bathtub Yourself.

At This Website